111-198-157A  Piston Ring Kit, 77mm

VW 1200 PISTON RING SET - 77 x 2.5 x 2.5 x 4mm

All rings for 1 engine

EMPI 9106 Fuel Shut Off Valve

Fits both stainless steel and aluminum gas tanks

VW Brake Line "T" 113-611-755

Chrome Steering Shaft

7/8 x 60 long

VW BALL JOINT DROPPED SPINDLE DISC BRAKE KIT

Replace your old VW front drum brakes with new VW disc brakes!

Fits all Link Pin Volkswagen Type 1 except Ball Joint and Super Beetle.

EMPI 8809 1 3/4" Complete Air Cleaner Assembly Fits Weber Progress - DFV-DFEV-DFAV

EMPI 3586 Cal Look Rubber Kit

Type 1, 58-64, 4-piece Set

High quality window rubber made without molding groove for that smooth Cal-Look.

EMPI 3708 Dual Racing Exhaust System - Black

Dual Style exhaust features great looks and maximum horsepower. Slip-joints allow for easy installation. Comes in black with muffler inserts. Eliminates heater boxes. Fits 1200-1600cc engines with single or dual carburetors except 48's / 51's

EMPI 9441-B Street Model Centrifugal Advance Dstributor with Electronic Ignition Eliminates Points and Condenser

Street Distributors have an advance curve and same tune-up components as the 009 and come complete with O-ring.

(Must be used with a coil with an internal resistor or an external ballast resistor must be used)

New Centrifugal Distributor 009

New 009 distributor is the perfect replacement for most aircooled VW engines. It is a centrifugal advance distributor. Comes complete with cap- rotor- points- and condenser. These distributors are a must whenever you plan to change to any after market carburetor kit.

VW Type 2 & 4 FLYWHEEL SEAL

For VW 1700-2000CC - Bus 72-79, Vanagon 80-83 and 84-92

This is also called the rear main seal.

VW ENGINE GASKET SET

Full engine gasket set for 1972-79 Volkswagen Bus, Vanagon, & Transporter with a 1.7, 1.8, 2.0L engine.

This is a complete set but it does not include the flywheel and crank pulley seals.

VW HEAT EXCHANGER LEVER KIT

For left side

VW HEAT EXCHANGER LEVER KIT

For right side

071-198-009A VW ENGINE GASKET SET

Full engine gasket set for 2000CC - BUS 1979 / VANAGON 80-83

This is a complete set but it does not include the flywheel and crank pulley seals.

VW TYPE 1 Aluminum Rhino High Performance Transaxle Transmission Case

NEW - 081-301-0512  //  98-3002-B

VW 78.8MM STROKE COUNTERWEIGHTED CRANKSHAFT

Multiple die stamp forged from 4340 chromoly, 78.8mm Stoke. Cranks are the magna fluxed, shot peened and all journals are nitrided, precision ground and micro polished. Additional features include cross-drilled chamfered oil holes, dynamic balancing, 8 dowel and extra long 8mm dowel pins. 

VW Rod Journals

Note: stroker cranks require machining of case and possibly other internal components for rod clearance.

VW FAN V BELT

High quality belt for use with a power pulley. 10�x 1000mm

Fits:

Type 3 63-73

VW FAN V BELT

High quality belt for use with a power pulley. 10�x 900mm

Fits:

Bug CV 54-60

Bug SDN 54-60

Bus 54-59

GHIA 56-60

Check MOFOCO.COM for VW Air-cooled items like this: VW TYPE 1 BUG 1955-67 IGNITION KEY CYLINDER AND SWITCH WITH KEYS 111-905-803D

VW OIL COOLER

Doghouse oil cooler for Volkswagen Type 1 1970-1978 & VW Type 2 1970-1971

VW Carburetor Base Gasket

For 1600CC engines from 1971-74

VW TAPERED TIP TAIL PIPES

Pair of tapered tail pipes for Volkswagen Type 1..... 1967-1972.

VW REAR BRAKE HOSE

210mm

Fits Volkswagen Type 1 1968-1979 IRS

VW REAR DISC BRAKE ROTOR

1 disc only

This is a replacement rotor for most rear disc brake conversion kits.

Fits swing axle thru 1968 long spline

VW REAR DISC BRAKE ROTOR

1 disc only

This is a replacement rotor for most rear disc brake conversion kits.

Fits swing axle WITH SHORT SPLINE

113-698-002 Front Brake Shoe Hardware Kit

Kits includes springs, pins and clips

Fits: Type 1 Bug 65-78, GHIA 65-66, Thing 73-74

VW OVAL HORN GRILLS

For Volkswagen Beetle Bug 1952-1967

Comes as pair

131-415-801B  Type 1 Adjustable Left Tie Rod 66-5/68

CV Drive Flange for VW Type 1 Transmission to Porsche 930 CV Joint

EMPI 16-2534 Single Pedal Assembly with Single Master Cylinder.

3/4" Brake/Clutch, fitting size is 1/8" NPT

Fully Polished with aluminum mounting bracket and high square reservoirs with easy fil cap

EMPI 16-2550 Brake Line Brass Fittings 1/8" NPT, 6pack

EMPI 16-2549 Clutch Slave Kit

Compatible with all hydraulic pedal assemblies.

Housing is tapped 1/8 NPT in two spots.  Female end of filtting is supplied is 3/8-24.  The other 1/8 NPT has a bleeder fitting in it

EMPI 16-9290 electric Speedometer to Cable Conversion Kit

This kit allows you to hook up an electronic speedometer into a Type 1 sedan without modifying your drums or rotors. The custom designed cable utilzes the OEM dust cap hole with an inductive sensor on the opposite end, which can be easily wired to your electronic speedometer

EMPI 16-9702 VW FULL FLOW OIL PUMP Thru 70, w/Flat Cam Gear, Each

Conventional oil filter to your engine with this 31.9mm oil pump with 1/4" NPT tapped inlet and outlet. 

Supplied with hardware and Gasket

Use P/N 9215 Fittings, Sold Seperately

EMPI 16-9713 VW FULL FLOW OIL PUMP 71 & Later, w/Dish Cam Gear, Each

Conventional oil filter to your engine with this 31.9mm oil pump with 1/4" NPT tapped inlet and outlet. 

Supplied with hardware and Gasket

Use P/N 9215 Fittings, Sold Seperately

EMPI 16-9901 6 Puck Clutch Disc

6 pads, 200mm with steel riveted hub

EMPI 16-9904 Bolt on Bowden Tube Bracket

Used for both Bowden tube and hydraulic clutch slave cylinders

EMPI 16-9908 Forged Heavy Duty Clutch Cable Arm

For: Type 1 61-71 and all 002 Type 2 Tansmissions

EMPI 17-2817 Clutch Slave Heim End 3/8" -24 THD, 3/8" Ball, Each

EMPI 17-2883 Billet Slave Cylinder Bracket, Type 1, Each

17-2975 Rear Truss Bar, Type 1, Kit

Triangulates the shock towers and the frame horns, helping to prevent movement of the engine and trans upon acceleration preventing wheel hop. Adjustable rod ends allow for variations and/or preload. Features 3/4" Steel Tubing, Powdered-coated black for good looks and durability.

Fits 1961 and Later Beetle, S/B and Ghia - Swing Axle and IRS. Does NOT fit Thing and will NOT fit with SR-17 and other tall starters.

Some applications may require slight trimming/modification to the body panels for installation.

 EMPI 21-4305 Lube A Lobe Lightweight Lifters

30mm

Sold in Sets of 8

EMPI 21-7510 Type 4 Cylinder Shim .010

EMPI 21-7520 Type 4 Cylinder Shim .020

VW Type 1 Replacement Rear Rotor BLANK. Short Spline. IRS & Swingaxle.

VW FRONT DISC BRAKE CALIPER BRACKETS

Caliper brackets to convert a Super Beetle Bug to disc brakes.

Rear Disc Brake Bracket

w/ Emergency Brake

Sold Each

VW TYPE 1 BEETLE / SANDRAIL REAR DISC BRAKE BRACKETS LEFT & RIGHT

# 6129-B (EMPI # 22-2848-B)

NEW - SOLD AS PAIR

EMPI 22-2890 Replacement Brake Pads

Empi 22-2906 Zero Off-Set Wide-5 Rear Disc Brake Kit w/E-Brake, IRS, 1968-1972, SwingAxle '68

LIMITED STOCK!!!

NEW EMPI REPLACEMENT ROTOR FOR 5/205 REAR WIDE TRACK - THREADED FOR 12mm & 14mm STUDS

EMPI # 22-2973-B

VW FRONT DISC BRAKE CALIPER BRACKETS

Caliper brackets to convert a Type 1 Beetle Bug to disc brakes.

EMPI 22-5281-7 Type 1 IRS Rotor Spacer

EMPI 22-6096 Emergency Brake Cable 68" overall length, Each

EMPI 22-6099 Emergency Brake Cable 72" overall length, Each

VW PRESSURE PLATE

High Quality OE Brand 200mm VW Full Diaphram Pressure Plate

For 1971 & newer Volkswagen Type 1, 2, 3s where the throwout bearing slides on the "candlestick."

Applications:
Beetle 1971-1977
Super Beetle 1971-1979
Bus 1971
Karmann Ghia 1971-1974
Type 3 1971-1973
Thing 1973-1974

VW HEAVY DUTY PRESSURE PLATE

High Quality O.E. Brand 200mm VW Full Diaphram Pressure Plate

For 1970 & older Volkswagen Type 1, 2, 3s where the throwout bearing hangs with two clips.

Applications:
Beetle 1967-1970
Bus 1962-1970
Karmann Ghia 1967-1970
Type 3 1963-1970

FRONT OUTER WHEEL BEARING

Fits: Type 1 & 3, 66-on, each

VWP 311-405-645

VW FRONT BRAKE HOSE

355mm

For Volkswagen Type 3 & Ghia 1967 & newer

EMPI 3158 Universal Shifter Box

EMPI 3182 Rear License Plate Bracket

Stock-style bracket bolt to rear deck lid.  Zinc Plated.

Fits Type 1,2,3 & 4

Origianl design was for 68-79 T-1

EMPI 32-1204 Clutch Installation Kit

10.9 zinc plated bolts, wavy washers and a clutch pilot tool to complete any VW clutch installation

EMPI 3238 Stock Style Dual Port End Casting Kit

Stock Style Dual Port End Castings for the look and fit of stock.  Come complete with necessary clamps and new intake boots.  Flange has notch n it.  New not rebuilt.  For Type 1,2 & 3

EMPI 33-1065 Laser Sand Seal Pulley Bolt-In

1 5/8" FLANGED J-TUBES FOR MERGED HEADER

For use with EMPI #7320

EMPI 3598 Rear Deck Lid Seal Type 1 50-77

EMPI 3666 SINGLE QUIET PACK

Fits all Type 2 EMPI 3 bolt small flange headers in the 1:00 position

EMPI 3696 Swivel Flange Stinger

The Swivel Flange Stinger Eliminates the guess work.  The stinger will rotate to any desired position until tightened.  

EMPI 3697 Swivel Flange Stinger, Chrome

The Swivel Flange Stinger Eliminates the guess work.  The stinger will rotate to any desired position until tightened.  

PHAT BOY MUFFLER FOR MERGED EXHAUST

Type 1 only

EMPI 3703 Phat Boy Merged Muffler Stainless Steel Type 1 only

EMPI 3780-1 Fiberglass-Wrapped Baffle

Fiberglass Wrapped Baffles reduce back-pressure

22mm Tru-Arc Piston Pin Retainers

Fits all 1300-1600 Type 1 Engines

set of 8

EMPI Deluxe Solex/Brosol Dual 40mm Carburetor Kit with EMPI Twist Linkage, Type 1

MADE IN BRAZIL  -  43-4416-0  -  NEW

Dual 40 Carb kits featuring Brosol/Solex 40mm carbs, cast EMPI manifolds, chrome top air cleaners with washable gauze filters but now with your choice of Original-Style Linkage or the NEW EMPI Twist Linkage, featuring Heim ends, Billet stand and 3/8" aluminum rods - better performance, easier set-up and linkage stays adjusted!

EMPI HPMX or IDF Hex Bar Linkage Kit for Type 1 &

Type 3

 43-5223-0  -  NEW

High quality linkage kits feature thick heavy duty mounting plates, aircraft quality heims and include all necessary hardware and gaskets.

Hex Bar is 18 1/2" Long (Used on P/N 43-6317, 43-6319, 43-7317, 43-7319, 47-6317, 47-6319, 47-7317, 47-7319, 43-7341, 43-7342, 47-7341, 47-7342 Series Kits)

WEBER DUAL 34 ICT CARBURETORS

Upgrade your single carburetor setup to dual Weber 34ICT's today! These Dual WEBER 34 ICT Kits are ideal if you are looking to increase performance without losing fuel economy. Comes complete with everything needed for installation.

Fits Type 1 Volkswagen dual port engines

EMPI 4395 Headliner Kit 68-77 Black

Features stock style vinyl and comes complete with door post covers.

Fits Type 1 and Super Beetle

EMPI 5001 Bench Mount Engine Stand

Mounts to work bench.  Features swivel head.  Use for holding engines or transmissions.  1 5/8" male tube that slides into mount.

EMPI 5007 Rolling Engine / Transmission Stand

Holds engine or transmission.  Features swivel head, HD Steel construction with metal casters for mobility.  Knock down style allows for UPS Shipments.

VW HEADLIGHT EYEBROWS PAIR

For Beetle Bug 1967 and on & early Splitty Bus

Provides that custom or classic look

VW CRANKSHAFT INSTALLATION KIT

This kit has everything you need to install a crankshaft into a 1200-1600cc VW engine. 7 PC KIT

EMPI 8670 FAN SHROUD 36hp no ducts

EMPI 8951 Front Firewall Engine Tin - Early, Black

Fits between engine and transmission

EMPI 9115 Polished Power Pulley w/holes, Black Numbers

Get a real increase in horsepower with the smaller diameter pulley.  Available in our exclusive 5 hole design, with black degree numbers and marks.  (Note:  Use with belt #9120)

Empi 9205 Brass T-Adaptor for Gauges 1/8"

EMPI 9355 VW Battery Isolator Switch & Seal Kit

Safety and security.  Features removable key.  The seal kit is a two piece kit that included one seal for the key shaft and one with a weather tight cap for the switch base.  For 6 or 12-volt systems.

EMPI 9445 Alternator Conversion Kit

Replace your 12-volt generator with a high-charging alternator. Kit comes complete with a new EMPI 55amp alterntor. Kit includes stand, strap and 3=piece backing plate set.

Also a great start for converting a 6-volt system to 12-volt

EMPI 9445-7 55-AMP ALTERNATOR

This is a 100% new air cooled VW alternator

Fits Dune Buggy, Beetle, Bus, Trike, BAJA, GHIA and Thing, 1500-1600cc

VW CHROME 90amp ALTERNATOR

EMPI Performance high output alternator for air cooled upright, Type 1 and Early Type 2 style engines. MADE IN THE USA. Produces 90 AMPs. Dual Internal Cooling Fans. Internal Regulator.

EMPI 9516 Wheel Studs, M12-1.5 Both Ends, Set of 5

EMPI 9517 Wheel Stud Kit, Set of 5

M14-1.5, Both Ends

VW TRANSMISSION MOUNT KIT

Volkswagen heavy duty steel saddle & mount eliminates flex

A must for Buggies

Zinc plated

VW COIL-OVER SHOCKS

New pair of adjustable coil over shocks

Chrome spring, black colored shocks

16 3/4" extended length

See item page for more details.

VW BALL JOINT COIL-OVER SHOCKS

New pair of adjustable coil over shocks with a ball joint front

Chrome spring, black colored shocks

18" extended length

See item page for more details.

EMPI 9580

Replacement Offset Wheel Stud for use with EMPI 9504

SOLD EACH

EMPI 9588

Replacement Wheel Stud for use with EMPI 9504

SOLD EACH

EMPI 9652 Rear Oil Shock

Fits: All IRS, Swingaxle, Type 1, Ghia, Type 2, Type 3

Includes two spacers to fit all the applications listed

Qty 1

EMPI 9656 Gas Shock, FRONT, Link Pin, Stock Height, EA

Gas shocks are far superior and longer lasting than oil filled shocks. Gas Charged Performance Shocks are specifically designed and engineered for the VW Beetle, with stock ride height or lowered suspensions.

EMPI 9656 Gas Shock, REAR, Link Pin, Stock Height, EA

Gas shocks are far superior and longer lasting than oil filled shocks.  These shocks are specifically designed and engineered for the VW Beetle, with stock ride height or lowered suspensions.

Fits: All IRS, Swing Axle, Type 1,2 & 3, GHIA

EMPI 9678 911 Alloy Wheels 15 x 4.5 Polished

EMPI 9680 911 Alloy Wheels 15 x 5.5 Polished

EMPI 9685 GT-8 Wheels Silver w/Polished Lip

EMPI 98-1006-B Front Bumper Blade 68-73

113-707-191C Bumper Bolts 68-73 Pack of 12

EMPI 98-1017-B Stock Rear Bumper Blade 68-73

Type 1 1971-later Quarter Air Grilles.

OUTER DOOR HANDLE W/KEYS

Outer Door Handle w/keys, 68 & Later, each 113-837-205M

FITS LEFT OR RIGHT

EMPI 98-1039 Stock Style Door Hanlde, Chrome, 56-66, Each

EMPI 98-1187 Type 1 87mm Piston Ring Set

EMPI 98-1190-B VW Piston Ring Set 90.5mm (1.5 X 2 X 4mm)

VW PISTON RING SET - 90.5MM

1.5 X 2 X 4mm Ring Size

All rings for 1 engine

98-2013 Stock Style Mirror, Type 1, thru 67, Round, Left, Each

use with Threaded Door Hinge Pin #98-2101 (sold separately)

98-2014 Stock Style Mirror, Type 1, thru 67, Round, Right, Each

use with Threaded Door Hinge Pin #98-2101 (sold separately)

OUTER DOOR HANDLES W/KEYS

Outer Door Handles w/keys, 1960-64

Sold as a Pair

EMPI 98-2048 Door Handle Seal Set 68-79

EMPI 98-2053 IGNITION SWITCH (ELECTRICAL ONLY), TYPE 1, 68-70

EMPI 98-2063-B VW Bug Inner Scraper, 4 clips

Fits '69-on

98-2101 Mirror Hinge Pin, Type 1, thru 67, Each

VW DRUM BRAKE HARDWARE KIT - FRONT

For Volkswagen Type 1Standard Beetle 1965-77

EMPI 98-7090-B Accelerator Repair Kit Only

For Type 1 67-79, Ghia 66-74, Type 3 64-73

EMPI 98-8644-B Synchro Ring 1st and 2nd Gear, Type 1 61 and Later, Type 2 61-75

EMPI 98-8645-B Synchro Ring 3rd and 4th Gear, Type 1 61 and Later, Type 2 61-75

EMPI 98-9501 Early H/L Lens, Type 2, thru 67, Glass

Each

EMPI 98-9533 VW Type 1 Turn Signal Assembly Fits 70-79. Left, drivers side.

EMPI 98-9534 VW Type 1 Turn Signal Assembly Fits 70-79. Right, passenger side.

EMPI 98-9549-B VW Type 1 Wiper Arm 1973-77 Drivers Side

EMPI 98-9550-B VW Type 1 Wiper Arm 1973-77 Passengers Side

Sotck Chevy Journal Rod Bearings

Stock Chevy Journal Rod Bearings

Stock Chevy Journal Rod Bearings, Stock Chevy Journal I-Beam Rod Bearings

(Sets Of 4).

EMPI 17-2732 Narrow Billet Mounting Bracket 1 1/2" tube, 2 1/8" wide

Carburetor Tune up Kit

EMPI 2231 Carburetor Tune up Kit VW Type 2, 73-74, Type 3, 64-67

Basic repair kit come complete with needle/seat, all necessary o-rings and gasket.

Kit also includes floats and accelerator pump diaphragms.

Carburetor Tune-up Kit WEBER 40 DCNF

EMPI 2345 Carburetor Tune-up Kit WEBER 40 DCNF

Basic VW carburetor repair kits comes with floats and accelerator pump diaphram, needle/seat and all necessary o-rings & gaskets.

Shine up your e-brake handle with this billet aluminum cover!

Fits all 1965-79 VW Beetles and 1974-79 Ghias

Chrome 3 gauge hole dash panel made to accept all 2 1/16" gauges.

Chrome 3 gauge hole dash panel made to accept all 2 1/16" gauges.

Chrome 2 gauge/1 tach hole dash panel made to accept all 2 1/16" gauges and 3 1/8" tachs.

VW GAUGE READY DASH PANELS

DASH PANEL IS MADE TO ACCEPT ALL 2 1/16" GAUGES.

CHROME PLATED

Chrome 2 gauge hole dash panel made to accept all 2 1/16" gauges

VW SWING AXLE SPACER KIT

Volkswagen Stock axle spacers just won't hold up to the abuse of off-road and high-performance applications. This super duty 4-piece hardened spacer set is the answer.

Thin spacer is 6.5mm thick with a 30mm opening.

Thick spacer is 18mm thick with a 30mm opening.

VW URETHANE BUSHING SHIFTER BOX

Fitting this on the back of the EMPI shift box will keep the shift rod in place.

Two self-tapping screws are needed to fasten box.

EMPI 16-5102 Urethane Shift Coupler, Early Style

The strength and durability of Urethane will out-last and out-perform standard rubber products in every application. 

Install Urethane and never look back!

VW TRANSMISSION SHIFT COUPLER

Much like the original one it replaces, this fits Volkswagen Type 1s 1965 and newer; and other applications that use this style of coupler.

The key improvement on this unit is the two inserts for the cage have been made out of urethane so the shifter linkage will be much tighter and responsive.

A must do upgrade for almost every car that uses this style of shift coupler!

EMPI 16-5109 URETHANE SNUBBER - LINK PIN, PAIR

VW URETHANE REAR SNUBBERS PAIR

The strength and durability of urethane will out-last and out-perform standard rubber snubbers. Install urethane and never look back!

Fits 1958-1979 Volkswagen Beetles.

VW URETHANE SPRING PLATE BUSHINGS PAIR

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.

Replaces early Volkswagen Type 1 & Type 3 style outer spring plate/torsion bar bushings

Bug, Ghia, Dune Buggy, Sandrail, Trike

See item page for more fitting information.

VW URETHANE SPRING PLATE BUSHINGS PAIR

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.

Replaces early Volkswagen Type 1 & Type 3 style outer spring plate/torsion bar bushings

Bug, Ghia, Dune Buggy, Sandrail, Trike

See item page for more fitting information.

VW URETHANE SPRING PLATE BUSHINGS PAIR

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.

1 3/4" inside diameter

Fits VW Type 1 style spring plate/torsion bars only

Bug, Ghia, Dune Buggy, Sandrail, Trike

VW URETHANE SPRING PLATE BUSHINGS PAIR

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.

1 7/8" inside diameter

Fits VW Type 1 style spring plate/torsion bars only

Bug, Ghia, Dune Buggy, Sandrail, Trike

VW BALL JOINT BUSHING KIT

Volkswagen front ball joint beam urethane bushings, inner and outer.

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.

4 pieces

EMPI 16-5161 Stainless Steel T-Bolt Style Alternator/Generator Strap

The ultimate alternator/generator strap. The great and long lasting looks, strength, and durability of stainless steel with the positive security of the t-bolt style. A must for off roading.

VW OIL FILTER MOUNT - IN FACING

VW bolt-on full flow oil filter mounts make filter mounting easy. Features inward and outward polished aluminum, these accommodate most off-road and drag race applications! All hardware included.

VW OIL FILTER MOUNT - OUT FACING

VW bolt-on full flow oil filter mounts make filter mounting easy. Features inward and outward polished aluminum, these accommodate most off-road and drag race applications! All hardware included.

EMPI 16-8242 UNDER FENDER OIL FILTER MOUNT, TYPE 1 THRU 73'

Remote Oil Fitler Mounts. Bolt-on full flow oil filter mounts make filter mounting easy. Covers street sedan applications by cleanly tucking the filter up under the rear fender on a black powder coated steel mount that attaches with the bumper bracket bolts. Hardware Included. 

VW OIL SUMP PLATE

This billet aluminum sump plate will never bend or distort due to over-tightening, unlike stock plates that can cause dangerous leaks. Since it is CNC machined from high grade aluminum billet, it also adds a custom look to any engine!

EMPI 16-9512 BILLET "OIL" FILLER CAP

Billet Oil Cap with "OIL" etched on the top 

Cap fits EMPI threaded filler tubes as well as most other threaded aluminum oil fillers

VW THREADED OIL GALLEY PLUG KIT

This kit is the first step to any quality engine build. By installing this 12-peice oil galley plug kit, you will realize the advantage and ease of cleaning and inspecting the "life blood" passages of your oiling system. Each kit contains seven 1/8" npt, two 1/4" npt, and three 3/8" npt threaded plugs. Machining of case required

Billet Type 3 Block off Kit

Empi 16-9516 Billet Type 3 Block off Kit Use on late style and Type 3 cases to block off oil fill opening to convert to upright applications. Complete with cast aluminum block-off plate and gasket.

Use on late style and Type 3 cases to block off oil fill opening to convert to upright applications. Complete with cast aluminum block-off plate and gasket.

EMPI 16-9519 Main Bearing Dowel Pin Set

This set of 5 dowel pins is used to align the main bearings. Includes five to do a complete install.

Fits all air cooled VW models

VW MINI OIL SUMP KIT

Help prevent oil starvation in your VW by installing this "mini" sump to increase oil capacityin your  VW Bus, Bug, or Ghia. Kit comes with 3 different size pick-up tubes, studs, nuts, and gaskets.

Your existing drain plug can be re-used, or use our magnetic drain plug.

VW OIL SUCTION KIT

This kit provides consistent oil pick up in your VW Bug, Ghia, or Bus. The supplied sump plate depression keeps the pick-up extension submerged in oil at all times.

The built in screen helps keep harmful particles from reaching vital engine components. This is a great addidtion to any performance-built engine to insure a longer engine life.

VW PERFORMANCE CRANKSHAFT GEAR SPACER

VW HEX HEAD OIL RELIEF SPRING PLUG

A long overdue solution to the removal of relief plugs. These threaded steel hex head plugs eliminate the need for that giant screwdriver.

Sold as one pair.

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 90.5-92mm cylinders

Installs between the top of the cylinder and the cylinder head. .040"

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 90.5-92mm cylinders

Installs between the top of the cylinder and the cylinder head. .050"

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 92mm cylinders

Installs between the top of the cylinder and the cylinder head. .060"

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 94mm cylinders

Installs between the top of the cylinder and the cylinder head. .040"

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 94mm cylinders

Installs between the top of the cylinder and the cylinder head. .050"

COPPER CYLINDER HEAD GASKETS

Set of four copper head gaskets for 94mm cylinders

Installs between the top of the cylinder and the cylinder head. .060"

34 PICT Carburetor Spacer

EMPI 16-9705 34 PICT Carburetor Spacer, Each Space up your 34 PICT Carburetor to clear the alternator

Each Space up your 34 PICT Carburetor to clear the alternator

VW TRANSMISSION SIDE COVER

Heavy duty aluminum side cover for swing axle

HEAVY DUTY SIDE COVER FOR IRS

EMPI 16-9905 Heavy Duty Aluminum Side Cover for IRS, each

EMPI 17-2795 King Pin Conversion Inner Bearing

VW KING PIN CONVERSION BEARING, OUTER

This outer bearing allows you to install ball joint rotors onto king pin spindles.

Requires new seals

Intake Manifold 30/31/34 Pict

EMPI 17-2805 Intake Manifold 30/31/34 Pict (Ref. P/N: 113-129-701AQ)

This manifold allows for the use of 30 PICT-1, 31 PICT-3 or 34 PICT-3 carburetors without adaptors.

Manifold flange is drilled for either stud pattern and comes with heat risers, gaskets, and 1/8" pipe plug.

Drilled and tapped for optional vacuum advance.

EMPI 17-2809 BILLET F/F OIL LINE BRACKET - BLACK, EACH

Billet full flow hose brackets.

Keep oil lines in check while maintaining that Billet look. Bolts on at exhaust flange and helps protect oil lines from engine and exhaust. Fits up to 3/4" O.D. Hose.

Also comes Polished, P/N: 17-2810

EMPI 17-2810 BILLET F/F OIL LINE BRACKET - POLISHED, EACH

Billet full flow hose brackets.

Keep oil lines in check while maintaining that Billet look. Bolts on at exhaust flange and helps protect oil lines from engine and exhaust. Fits up to 3/4" O.D. Hose.

Also comes in black, P/N: 17-2809

VW BUG ENGINE NARROW OIL SUMP W/ FILTER

Cast aluminum oil sump is only 1 3/4" deep. Adds oil capacity and offers improved filtration and easy bolt on installation. Filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

VW MINI OIL SUMP WITH FILTER

Cast aluminum mini sump.

Replaces your stock oilscreen and cover and offers improved filtration, helps prevent oil starvation during hard cornering and easy bolt-on installation.

Filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

VW BUG ENGINE CASE OIL DUAL BYPASS ADAPTER

This adapter allows you to run both your stock oil cooler, along with an external cooler and/or a remote oil filter.

Fits VW Type 1 with minimal trimming of the sheetmetal. Will not fit doghouse-style coolers.

VW OIL SUMP FILTER

Replacement filter for 17-2871 & 17-2872

Offers improved filtration as easy filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

EMPI 17-2878 - VW Bug Type 1 Dual Circuit Master Cylinder Reservoir Mounts on Top

Billet Combo Fuel Pump Block-off/Coil Mount

EMPI 17-2926 Billet Combo Fuel Pump Block-off/Coil Mount

Polished aluminum Combo Mount serves as a fuel pump block-off, breather vent and ignition coil holder.

Features a 3/8 NPT outlet for vent.

Great looking and functional.

Hardware and gasket included.

EMPI 17-2941 OIL FILLER & BREATHER BOX KIT

The EMPI dual-purpose Oil Filler & Breather Box includes a system of internal baffles that separate the oil from the air then returns the oil back to the engine. It mounts upright on the alternator stand making for easy oil filling and was designed to look like part of the engine. The Billet Aluminum filler cap seals with an o'ring. Aluminum construction offers great looks and leak-free operation featuring an o'ring seal and button-head allen top screws. Vent your valve covers, crankcase, air cleaners...whatever your requirements. Comes with attaching nut, o'rings, gasket and instructions.

EMPI 17-2943 BILLET OIL FILLER CAP

Polished Billet Aluminum Cap with knurled edge for easy grip offers a great finishing touch to any breather tube.

Fits: P/N 17-2941 and alternator stands.

EMPI 17-2946 BILLET ALUMINUM OIL COOLER BLOCK-OFF

Billet Aluminum Oil Cooler Block-off

Show quality Polished Billet Aluminum oil cooler block-off. 

Comes with Allen Head Cap Screws for a clean installation along with gasket and hardware.

EMPI 17-2976 Rubber Flange Gauze Air Cleaner

Oval Gauze Rubber Flange Air Cleaner for Stock VW Carb., 2" Neck, 4 7/16"x6 7/8"x2 3/4" High

Featuring a washable and reusable Chrome top and Gauze Filter, they add style and performance and fit most upright applications. Constructed with a super strong molded pliable rubber lfange which absorbs vibration. Neck can be stretched up to 1/16" for added applicatons. Use with or without 90 degree Nylon Vent tube (included). Comes with clamp.

VW BRAKE MASTER CYLINDER

22.2mm

For all Volkswagen Type 2 to 1967

EMPI 1.25 Rocker Arms, W/Bushing, Set

1.40 ROCKER ARMS

EMPI 2164 EMPI 1.40 Rocker Arms, w/Bushing, Set

These superior quality chromoly rockers are just the answer for either a mild street or a hi-performance competition engine.

EMPI's rocker arms are made from forged chromoly and then precision ground and heat treated.

Not only are these the strongest rocker arms available, they are also drilled through on the alloy adjusting screws so both screws and rocker arms are fully lubricated.

All shafts, blocks and shims are high strength alloy as well. Precision ground bronze bushings with through hole lubrication ensures that premature failure of the old needle bearing rocker arm design is a thing of the past.

Chromoly rocker arm studs are provided to complete this kit and make installation and use a trouble free experience.

HI PERFORMANCE ROCKER SHAFT KITS

EMPI 21-2308 Hi-Performance Rocker Shaft Kit w/floating Center Spacer

Increase the RPM potential of your engine and get more power.

EMPI's rocker shaft kits help eliminate rocker shaft side play that casues rocker arm galling, clip and washer failure.

Has a floating aluminum center spacer which allows for "fine tuning" of rocker arm geometry and positioning.

All necessary hardware is included.

Increase the RPM potential of your air cooled Volkswagen engine and get more power.

EMPI 21-2309 Hi Performance/high Strength Rocker Shaft Kit

Our high-strength Rocker Shaft Kit helps eliminate rocker shaft side play that causes rocker arm galling and clip & washer failure.

Our kit includes two precision ground high strength shafts, hardened steel spacers & solid shims, and all necessary installation hardware is included.

Can be used with either stock 1:1 rockers or our high performance 1.25:1 rockers for added power!

Best when used with EMPI's swivel foot adjusters.

EMPI 21-2310 Rocker Arm Stand Shims, 12 pcs

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Includes 4pcs., each of .015", .030", and .060"

An easy and inexpensive way to get more power and acceleration from any 1200-1600cc Volkswagen engine.

No special modifications are needed!

Works with stock VW rocker shafts, push rods, and adjusters!

These 1.25 Rocker arms will not affect cam duration; they increase lift throughout the entire cycle.

Does not sacrifice bottom end performance and can be run with stock carburetors.

Set of new screws and new nuts to use for adjusting the valves on a Type 1 VW valve train

Works with our 1.25:1 rocker arms too!

Chromoly rocker studs are superior in strength to stock VW rocker studs

A must have for high-performance heads with dual valve springs!

Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold in sets of four.

Chromoly rocker studs are superior in strength to stock VW rocker stud

A must have for high-performance heads with dual valve springs!

Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold each.

ROCKER ARM STAND SHIMS

EMPI 21-2315 Rocker Arm Shims, .015", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

ROCKER ARM STAND SHIMS

EMPI 21-2330 Rocker Arm Shims, .030", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

ROCKER ARM STAND SHIMS

EMPI 21-2360 Rocker Arm Shims, .060", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

EMPI 21-4310 VW High Grade Camshaft Gear Bolts

Cam Vw Bug Set of 3 for attaching P/N 21-2500 aluminum cam gear.

VW .03" CYLINDER HEAD SPACERS

VW steel cylinder head spacers (.030") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. For VW 1500-1600cc engines.

VW .06" CYLINDER HEAD SPACERS

VW steel cylinder head spacers (.060") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. For VW 1500-1600cc engines.

VW .010" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs.

Fits VW Type 1 engines.

For 85.5mm cylinders.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines. For 85.5mm cylinders.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines.  For 85.5mm cylinders.

VW .04" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines. For 85.5mm cylinders.

VW CYLINDER SHIMS

.060" cylinder shims for VW Type 1. 85.5mm cylinders

These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs.

VW .09" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs.Fits VW Type 1 engines. For 85.5mm cylinders.

VW .01" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders. For VW Type 1 engines.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .04" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .060" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 and 92mm bore VWs.

90.5mm/92mm Cylinder Shims

EMPI 21-7076 90.5mm/92mm Cylinder Shims .090"

Steel shims allow for adjusting deck height without machining the pistons.

Corrects for increase in stroke and compensates when case is surface machined.

For standard 8mm studs and 10mm studs.

Sold in sets of 4.

VW CYLINDER SHIMS

.010" cylinder shims for VW Type 1. 94mm cylinders

These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs.  Set of 4. Fits 94mm bore VWs.

VW .040" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs.  Set of 4.  Fits Type 1 VWs with a 94mm big bore.

VW .06" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs.

VW .09" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs.

VW .04" CYLINDER HEAD SPACERS

VW steel cylinder head spacers (.040") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. Set of 4.

VW FRONT END ADJUSTER, BALL JOINT

For use on models from 1966 and LATER

Requires one on each tube; cutting and welding required!

VW FRONT END ADJUSTER, LINK PIN

For use on models from 1965 and prior.

Requires one on each tube; cutting and welding required!

VW CASTER SHIM KIT

Aluminum caster shims correct and improve front end geometry on your lowered Volkswagen.

Bug, Ghia, Type 3

Use longer bolts, EMPI 22-2816, for proper thread grip at pan head.

VW CASTER SHIM BOLTS

These are the bolts that hold the axle beam to pan.

They are longer to allow for the caster shims; but they can still be used to replace a stock bolt.

Work well with EMPI 22-2815 caster shims

VW BALL JOINT CAMBER ADJUSTERS

Camber adjusters for ball joint front end

For use with stock or lowered VW front ends

VW CLEARANCED BALL JOINT, UPPER

Specially modified ball joints provide more suspension travel on lowered or raised Bugs.

Fits all Type 1 Volkswagens from 1966-77

VW CLEARANCED BALL JOINT, LOWER

Specially modified ball joints provide more suspension travel on lowered or raised Bugs.

Fits all Type 1 Volkswagens from 1966-77

VW NARROWED LEAVES

Narrowed leaves/axle beam tortioned leaves for link pin

Fits Type 1 Volkswagens

Two sets required for narrowed VW front end

VW DROP SPINDLES

2.5 inch drop spindles for link pin axle with drum brakes

Fits 1965 and earlier VW Bug, Buggy, Ghia

See item page for more details.

VW DROP SPINDLES

2.5 inch drop spindles for ball joint axle beam with drum brakes

Fits 1966-1977 VW Bug, Buggy, Ghia

See item page for more details.

VW REAR DISC BRAKE CONVERSION KIT

VW rear disc brake conversion kit with emergency handbrake for all Swingaxle Type 1s & IRS 68-72. Includes Beetles, Buggys, Sandrails. Kits are available for both swing axle and IRS Type 1 based applications. All kits come complete with rotors, calipers, cables all necessary hardware.

Standard 4x130 bolt pattern

VW REAR DISC BRAKE CONVERSION KIT

VW rear disc brake conversion kit with emergency handbrake for all IRS & Swingaxle Type 1s. Includes Beetles, Buggys, Sandrails. Kits are available for both swing axle and IRS Type 1 based applications. All kits come complete with rotors, calipers, cables all necessary hardware. This deluxe kit comes with HD cast mounting brackets

Standard 4x130 bolt pattern

VW REAR DISC BRAKE CONVERSION KIT w/E-Brake

VW rear disc brake conversion kit with emergency handbrake for Type 1 Bug, Beetle, Ghia IRS 1973-1979. Kit comes in Standard VW 4x130 Bolt Pattern with 14 x 1.5mm threads (not included in kit). Kit does include Rotors, Calipers with brake pads, Emergency Brake Cables, Caliper Mounting Brackets, Axle Spacers, Gaskets & Hardware

VW REAR DISC BRAKE CONVERSION KIT w/E-Brake

22-2871-F

*Deluxe Kit with Forged Brackets*

VW rear disc brake conversion kit with emergency handbrake for Type 1 Bug, Beetle, Ghia IRS 1973-1979. Kit comes in Standard VW 4x130 Bolt Pattern with 14 x 1.5mm threads (not included in kit). Kit does include Rotors, Calipers with brake pads, Emergency Brake Cables, Caliper Mounting Brackets, Axle Spacers, Gaskets & Hardware

Front Disc Brake Kit

Wide 5 VW Bolt Pattern

EMPI 22-2880 Front Disc Brake Kit, Link Pin, 5 lug, 5/205, 15" Rims to 65

A special brake rotor and caliper mount bracket combined to give you a premium disc brake upgrade using your existing front spindles.

Kit comes complete with master cylinder, brake lines, floating calipers with brake pads, wheel bearings, grease seals and all necessary hardware.

Now you can have the stopping power of disc brakes and have the early 5 on 205 rim of your choice, and no adapters!

WILL NOT WORK WITH DROP SPINDLES.

Caliper guide pins pre-installed.

VW REAR DISC BRAKE PADS

Rear disc brake pads replacement for EMPI Calipers.

These are the pads that are used in many of the rear disc brake kits that EMPI sells.

For rear calipers with emergency brakes.

Wide Rear Disc Brake Kit w/o E-Brake

EMPI 22-2930 Wide Rear Disc Brake Kit w/o E-Brake

5/205, Swing Axle 58-67 Wide Track rear disc brake kits are for Off-Roaders who are looking to increase their rear wheel "track".

Kits are without emergency brakes, and come complete with 1-piece minimum offseet 1" extra wide rotors, calipers, pads, mounting brackets, and all necessary hardware and gaskets for the complete installation.

Rotors are threaded for 12mm and 14mm studs.

VW DROP SPINDLES

2.5 inch drop spindles for link pin axle with disc brakes

Fits VW Bug, Buggy, Ghia with disc brakes

See item page for more details.

VW DROP SPINDLES

2.5 inch drop spindles for ball joint axle beam with disc brakes

Fits all Type 1 ball joint front end

See item page for more details.

PADS FOR STEEL BRACKET KITS

EMPI 22-2966 Pads for Steel Bracket Kits

Set of 4

VW FRONT DISC BOLT-ON BRAKE KIT

VW front disc brake kit for link pin style applications. Bolt-on 5/130 pattern.

Kit includes bolt-on heavy duty brackets and conversion bearings. Hardware included. Four bolt pattern shown for picture only.

Carburetor Tune up Kit

EMPI 2202 Carburetor Tune up Kit WEBER Progressive, DFV, Holley 5200, EPC 32/36F (VW).

Basic repair kit come complete with needle/seat, all necessary o-rings and gasket.

Kit also includes floats and accelerator pump diaphragms.

Carburetor Tune up Kit

EMPI 2238 Carburetor Tune up Kit Holley Bug Spray

Basic repair kit comes complete with needle/seat, all necessary o-rings and gasket.

Carburetor Tune up Kit Zenith 32NDIX - Minor

EMPI 2258 Carburetor Tune up Kit Zenith 32NDIX - Minor. 

Basic repair kit come complete with needle/seat, all necessary o-rings and gasket.

VW CARBURETOR REPAIR KIT

Basic VW carburetor repair kits comes with accelerator pump diaphram, needle/seat, and all necessary o-rings & gaskets.

Note: kit includes all parts needed for one carburetor; if dual carb engine, two kits are needed.

Kit parts include only what you see in picture

EMPI 2365 Carburetor Tune-up Kit

WEBER 34 ICH, EPC 34X

34ICT

The kit is a basic repair kit and comes complete with needle/seat, all necessary 0-rings and gaskets. 

VW HOOD HOLD DOWNS

One pair of rubber hood hold downs for VW hoods

4 3/4" overall length of rubber

For VW Beetles, Dune Buggies, & Sandrails. A must for your Baja Bug!

See item page for more information.

VW HIDDEN STEREO GLOVE BOX

A glove box made with a built-in area to mount your stereo. Perfect for applications where security is an issue or when modifications to the stock dash are not desired.

Fits VW Bug Beetle from 1958-64.

Made from durable black plastic.

Designed for left hand drive models. May not fit right hand drive models.

VW OIL PUMP COVER

Precision machined from cast iron with a high quality finish & ground gear/gasket surface, this is the best pump cover available! Impoved design decreases pulley and sheet metal clearance issues.

Cover is threaded 3/8" NPT and comes with complete 1/2" hose fitting & gasket.

Fits all VW pumps with 8mm bolt holes.

Electric Fuel Pump Mount Kit

EMPI 31-3010 Electric Fuel Pump Mount Kit

Fuel Pump Mount Kit allows for the installation of EMPI or Facet electric fuel pumps in the stock pump location. Hardware and gasket included.

Billet Fuel Pump Block-off w/hardware

EMPI 31-3011Billet Fuel Pump Block-off w/hardware

Fuel Pump Block-off/Mount Block off with 12mm threaded breather boss.

Block off in high tech polished Billet aluminum. Includes mounting gasket.

EMPI 3137 Replacement Pins & Clips, Long, Pair

HYDRAULIC PARK LOCK

This hydraulic park lock holds your Volkswagen brakes locked by using line pressure.

Just push brake pedal down and then push the park-lock lever. (Not to be used as an emergency brake)

Lock should be placed by your shifter. It should interrupt the break line to the rear.

EMPI 3157 Belly Pan Gasket

Installs between body and pan providing a water-tight seal.

Great for body-off restorations, Kits cars, Baja Bugs and Dune Buggies

VW CABLE SHORTENING KIT

Shorten your clutch, emergency brake and throttle cables quickly.

A must for all buggies that have shortened pans.

CLUTCH CABLE SHORTENING KIT

Shorten your clutch cable quickly and easily.

A must for off-road Buggies!

VW E-BRAKE CABLE SHORTENING KIT

Shorten your emergency brake cable quickly and easily.

A must for Volkswagen Buggies with shortened pans.

VW THROTTLE CABLE SHORTENING KIT

Shorten your Volkswagen throttle cable quickly and easily.

End is designed for use with barrel nut.

VW THROTTLE CABLE EXTENDING KIT

2-piece Volkswagen throttle cable extending kit that can be installed onto the existing end of a throttle cable.

VW STEERING SHAFT SUPPORT

This Volkswagen steering shaft support fits 7/8" sterring shafts and is self-aligning for easy installation.

Features an oil impregnated bronze bushing with oiling cup for longer life!

VW TRANSMISSION MOUNT KIT

This Volkswagen Bug to Bus transmission mount kit allows for installing a Type 2 I.R.S. transmission into a Type 1 chassis. Featuring a heavy duty steel saddle, mount, and straps, eliminate your stock mounts & saddle for maximum support with no flex. A must for competition use!

Your particular application will dictate the proper axle length needed. CV's and components you may need.

VW THROWOUT BEARING

This EMPI branded throwout bearing fits VW models 1970 & earlier: Bug / Beetle, Karmann Ghia, Type 2 Bus Transporter, and Type 3.

VW SMALL INTAKE BOOT CLAMPS

For Type 1 Volkswagen dual port engines.

Sold in pairs.

VW LARGE INTAKE BOOT CLAMPS

Sold in pairs.

VW INTAKE MANIFOLD GASKETS

Fits Type 2 & Type 4 engines; 1700-2000CC. 3 & 4 bolt gaskets.

Sold in pairs.

VW DUAL PORT INTAKE MANIFOLD END KIT

This dual port intake manifold end castings kit is thick enough for porting and polishing. Made for VW 71-74 dual port engines.

These new ball burnished aluminum end castings come complete with necessary hardware and intake boots. Replaces VW part # 113-129-709G & 113-129-710D

EMPI 3245 Carburetor Adaptor For Alternator Conversion

Sometimes necessary when doing an alternator conversion. Spaces up the stock carburetor.

Comes with studs, nuts, and gaskets.

FOR 28/30 PICT CARBURETORS ONLY!

VW INTAKE MANIFOLD GASKETS

Dual port intake manifold gaskets for dual 40mm carburetors.

Sold in pairs.

VW INTAKE MANIFOLD GASKETS

Dual port Volkswagen intake manifold gaskets with larger intake face.

Sold in pairs.

EMPI 33-5000 OIL THERMOSTAT ONLY W/3/8" NPT

Mounts in-line and bypasses oil cooler until oil warms up to approximately 175 degrees. 

Always partially open to avoid over pressurizing. 

A must in performance and cold-weather applications.

Sold separately, fittings P/N: 9211 or 9212 and clamps P/N: 9225

For complete kit with fittings and clamps P/N: 33-5010

EMPI 33-5010 OIL THERMOSTAT W/FITTINGS AND CLAMPS

Mounts in-line and bypasses oil cooler until oil warms up to approximately 175 degrees. 

Always partially open to avoid over pressurizing. 

A must in performance and cold-weather applications.

VW EXHAUST SYSTEM

Single Quiet System Type 1 & Ghia, 1300-1600cc, 66-73 These precision designed systems feature 1 1/2" Tubing and Large 3 Bolt Muffler Flange. Mufflers feature Black tips. All systems include aluminum flex hose and installation kit.

VW CARBURETOR BASE GASKETS

TWO Base gaskets for 40/44 IDF/DRLA Volkswagen carburetors.

VW HEATER BOX J-TUBES

J-Tubes replace stock heater boxes, eliminating heater and saving weight. Fits most heater systems and includes gaskets.

Sold in pairs. Fits all up-right engines.

VW TYPE 1 ALUMINUM HEATER HOSE

Contains no paper. Heat and corrosion resistant to 450 degrees.

Sold Each

VW MUFFLER FLANGE GASKETS

Package of two VW large 3 bolt exhaust flange gaskets

VW EXHAUST PORT GASKETS

Pack of four 1 1/2" I.D. gaskets

For Volkswagens with1200-2332cc engines

VW EXHAUST TO HEAD GASKET

Fits 1200cc-2332cc Volkswagens

VW MUFFLER FLANGE GASKETS

Package of two VW small 3 bolt exhaust flange gaskets

EMPI 3395 Exhaust Port Gasket, 1200-1600cc, 1 5.8"

Pack of 4

VW CARBURETOR BASE GASKET

A VW carburetor base gasket for Weber Carburetors; 40/44/48 IDA Gasket

EMPI 3405 Muffler Flange Gasket, 2-Bolt

Pack of 2

VW MUFFLER FLANGE

Volkswagen large 3 bolt muffler flange.

2 9/16" I.D.

VW EXHAUST SYSTEM

New 4-tip "Monza" GT style exhaust system that fits 1600cc based Type 1 Volkswagen engines.

These are also great for kit cars like Bradley, GT, etc.

Note: this item has about 1 3/4" less ground clearance than the 2-tip mufflers do.

VW EXHAUST SYSTEM

This chrome two tipped VW GT muffler with header looks and sounds great! Use it with heater boxes or J-Pipes. The chrome tips line up with stock VW cut-outs on Bug rear apron.

Works with VW Type 1 1500cc, 1600cc, and larger. Also works well on Speedster replicas!

VW HEAT RISER BLOCK-OFF PLATES

These block-off plates cover heat riser flanges when intake heat riser is not used. A must when installing most dual carburetor kits.

Includes gaskets.

VW EXHAUST SYSTEM

This single-tip GT exhaust system muffler gives your Volkswagen a european look. Featuring chrome tips with built in resonators for that unique "GT" sound!

Fits 1300-1600cc engines including Volkswagen Type 1, Ghia, and Type 2 (1963-1971)

VW EXHAUST FLANGES

These 1 3/8 I.D. flanges bolt directly to Type 1 VW heads and can be used when creating or customizing an exhaust system for your VW engine.

Sold as pair

VW FRONT LEFT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails. Requires cutting fitting and welding.

VW FRONT RIGHT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails.  Requires cutting fitting and welding.

VW REAR LEFT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails. Requires cutting fitting and welding.

VW REAR RIGHT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails.  Requires cutting fitting and welding.

VW EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 1 & Ghia 1200-1600cc. Will NOT work with Type 3.

All systems include aluminum flex hose and installation kit.

VW DUAL QUIET EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 1 & Ghia, 1300-1600cc, 66-73

All systems include aluminum flex hose and installation kit.

TYPE 3 VW HEATER BOX J-TUBES

J-Tubes replace stock heater boxes, eliminating heater and saving weight. Fits most heater systems and includes gaskets.

Sold in pairs.

VW EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 3, 1500-1600CC.

All systems include aluminum flex hose and installation kit.

VW MUFFLER FLANGE

Small 3 bolt Volkswagen muffler flange

1 3/4" I.D.

EMPI 3844 VW SEAT BELT BUG BUS DUNE BUGGY 2 POINT LAP

EMPI 3851 VW 3 Point Seat Belt Harness Type 1 Bug

3 point retractable seat belt harness for 68-79 Type 1 VWs. Made from 2" automotive black web material. Comes complete with hardware and mounts to stock anchor locations.

VW CHROMOLY CASE STUD KIT

These chromoly case studs provide the superior and even clamping force required by today's high performance air cooled VW engines. The high grade chromoly studs are precision machined to resist stress and fatigue.

8mm in diameter, which is the stock VW diameter.

Includes O.E. style hardened washers and hex nuts

For Single Port cylinder head engines

Replaces original Volkswagen part number 043-198-355P.

DUAL PORT ENGINE CHROMOLY CASE STUD KIT

These 10mm chromoly case studs provide the superior and even clamping force required by today's high performance air cooled VW engines. The high grade chromoly studs are precision machined to resist stress and fatigue and are made for dual port head based engines.

For VW Type 1 71-79, Ghia 71-74, Type 2 71, & Type 3 71-73

Includes O.E. style hardened washers and hex nuts.

CHROMOLY CASE STUDS

EMPI 4010 10mm Chromoly Case Studs +12.7mm for Duel Port Heads VW

10mm C/M Case Studs +12.7mm for Duel Port Heads CHROMOLY CASE STUDS EMPI's Chromoly Case Studs provide superior and even clamping force required by today's hi-performance VW engines.

Our Chromoly Studs are made from high-grade Chromoly and precision machined to resist stretch and fatigue.

EMPI Chromoly Case Studs are available with 8mm or 10mm threads, stock length or +12.7mm longer for stroker applications or other variables.

Each kit is complete with O.E. style hardened washers and hex nuts.

VW CASE SAVERS

Repair stripped and worn head stud threads with these Volkswagen case saver inserts. Provides a great hold and comes in sets of 8.

(10mm ID x 1/2" O.D.)

VW CASE SAVERS

Repair stripped and worn head stud threads with these Volkswagen case saver inserts. Provides a great hold and comes in sets of 8.

(10mm ID x 14mm O.D.)

VW DELUXE ENGINE HARDWARE KIT

You get all the necessary hardware you need to assemble your VW beetle-style engine just the way it rolled off the line! This 8mm set includes case half sealing nuts, 15mm head nuts, and extra thick hardened washers.

VW DELUXE ENGINE HARDWARE KIT

You get all the necessary hardware you need to assemble your VW beetle-style engine just the way it rolled off the line! This 10mm set includes case half sealing nuts, 15mm head nuts, and extra thick hardened washers.

DUAL PORT ENGINE CHROMOLY CASE STUD KIT

These 8mm chromoly case studs provide the superior and even clamping force required by today's high performance air cooled VW engines. The high grade chromoly studs are precision machined to resist stress and fatigue and are made for dual port head based engines.

For VW Type 1 71-79, Ghia 71-74, Type 2 71, & Type 3 71-73

Includes O.E. style hardened washers and hex nuts.

Replaces original VW part #043-198-035DP.

VW CHROMOLY CASE STUD KIT

This is an 8mm chromoly case stud kit +12.7mm longer for stroker applications or other variables.

These case studs provide superior and even clamping force required by todays high-performance engines. The chromoly studs are made from high grade chromoly and precision machined to resist stress and fatigue. For dual port heads.

Includes O.E. style hardened washers and hex nuts.

10MM SELF TAPPING CASE STUD

A quick repair for stripped head studs. The rolled threads of this 10mm stud provide maximum hold and metal chips are effectively collected by the slot or hole design. Hole shown in picture but could have slot.

Measures 9 3/8" (240mm) long.

HI-PERFORMANCE CHROMOLY GLAND NUT - 36MM

EMPI 4026 Chromoly Gland Nut w/washer

Don't take a chance on stock gland nuts in high performance applications.

This ultra strong bad boy is made from 4130 chromoly. 

The extra strength chromoly and concave spring steel washer provide maximum holding power. Fitted with special pre-greased needle bearing and grease seal. 

Compatible with stock 4 dowel pin and 8 dowel pin flywheels and features a 36mm nut size, NOT a 1 7/8"

VW GLAND NUT WASHER

Heavy duty gland nut washer for Type 1 Volkswagen applications.

VW HI-PERFORMANCE PUSH RODS

These VW hi-performance pushrods resist flexing at high RPM's under loads of high lift cams and heavy valve spring pressures. A must with any dual spring application. Made from the highest quality heat treated 5/16" steel tubing, ends are pre installed and pushrods are 11.078" overall length! Set of 8 rods.

Prevent VW engine damage due to valve float or worn and weak valve springs!

Dual Valve Springs are a must for high-rev applications

Approximately 180 lbs. seat pressure at 1.550" installed height

For Type 1 Based Engines

Dual spring setup, set of eight (16 pieces)

Requires machining of your heads if the heads are not dual-spring already. MOFOCO can provide this service!

Prevent VW engine damage due to valve float or worn and weak valve springs!

Approximately 135 lbs. seat pressure at 1.550" installed height

For Type 1 Based Engines

Single spring setup, set of eight

Everything you need to prepare your heads for high-lift cam use and high RPM applications in one kit!

For Type 1 Based Engines

Single spring setup, kit includes high performance valve springs, light weight aluminum alloy retainers, and hardened valve locks.

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.015" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.030" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.060" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.010" shims... sold in sets of eight!

Everything you need to prepare your heads for high-lift cam use and high RPM applications in one kit!

For Type 1 Based Engines

Dual spring setup, kit includes high performance valve springs, light weight aluminum alloy retainers, and hardened valve locks.

Requires machining if your heads are not already dual spring setup. MOFOCO can provide this service!

Prevent valve stem wear caused by the side load of high lift cams and high valve spring pressure.

SOAK OVERNIGHT IN OIL BEFORE INSTALLING

CHECK OIL HOLES IN ROCKERS FOR FREE FLOW

VW 85.5MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 85.5mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 90.5MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 90.5mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 92MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 92mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 94MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 94mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

Pressure Plate

EMPI 4080, 1700lb/ Pressure Plate (Boxed).

The latest addition to the EMPI high performance line. Perfect for drag race, sand/off-road or high performance street applications. This 200mm pressure plate is rated at 1700 lbs, and are factory balanced with the removable center ring to cover both early and late transmission.

VW CLUTCH DISK

A Volkswagen super duty 200mm clutch disc with spring center.

Spring steel center disc dampens disc action for a smoother engagement. Metal woven lining resists slip under heavy clamp loads to put horsepower to the ground!

EMPI 4099 CHROMOLY FLYWHEEL, 12-VOLT, 200MM

This chromoly version of our lightened flywheel is the answerfor anyone looking ofr the ultimate in durability under extreme conditions. One piece chromoly construction and offset 8-dowel hole pattern along with a weight of approximately 13lbs., make this fully balanced flywheel the best option for a high performance engine. 12-volt 200mm (130 teeth) O-ring style.

VW ELECTRIC FUEL PUMP

Solid state reliability pumping 30 G.P.H. @ 2 to 4 P.S.I. usable with gas or alcohol! Very popular on VWs and works great with Weber, Dellorto, Kadron, EMPI, or stock VW carburetors.

Includes fuel line nippes

No pressure regulator required, however it is highly reccomended that one be used with these pumps on a carburetor application.

Bronze bushing for installing a 12 volt starter in a 6 volt transmission

VW SPARE TIRE WHEEL COVER

This black cover allows you to cover the spare tire on front of your Type 2 Volkswagen Bus or replace your existing cover.

Fits early and late Type 2 wheels.

VW UNI-LINK KIT

This adaptor kit allows you to fit your linkage to any DFV/DFEV Progressive Carburetor.

BROSOL / SOLEX DUAL 40MM CARBURETORS

Upgrade your single carburetor setup to dual Brosol / Solex 40mm carbs today! These Dual Brosol / Solex Kits are perfect if you are looking to add some performance to your project. Comes complete with everything needed for installation.

Fits Type 1 Volkswagen dual port engines

VW EXHAUST & INTAKE NUTS

For 8mm threaded stud, but with smaller 11mm wrench size for easier access than the regular 13mm nuts.

WEBER DUAL 40 IDF CARBURETORS

Upgrade your carburetors to dual Weber 40IDF's today! This dual weber kit is a must for your performance dual port engine. Comes complete with everything needed for installation.

Fits Type 1 Volkswagen dual port engines

VW TRIGGER SHIFTER

Long trigger shifter for all Volkswagen Bug & Ghia, 13 1/2" O.A.L

Trigger shifter features round chrome shaft with sliding trigger to release lock-out.

Also available with short or long shaft and extra-long shaft for bus applications.

VW TRIGGER SHIFTER

Short trigger shifter for all Volkswagen Bug & Ghia, 12" O.A.L

Trigger shifter features round chrome shaft with sliding trigger to release lock-out.

VW T-HANDLE SHIFTER

Aluminum T-Handle shifter for Volkswagen Bug, Dune Buggies, Sandrails, Trikes, and Ghias;

12 1/2" overall length.

Get through the gears in style with this precision made polished aluminum shifter. It has a reverse lockout button,"EMPI" cast into the handle, and comes supplied with a reverse lockout plate.

VW QUICK SHIFT KIT

Shorten the throw of your stock shifter up to 40%.

Fits all Type 1 except Autostick.

EMPI 4526-B Pedal Assembly Vw Ghia Buggy Sandrail Bug

Type 1 VW pedal assembly, fits all Beetles. Great for replacing a rusted out pedal assembly in your Beetle! It is also essential when building a Dune Buggy or Sandrail. Replaces EMPI 4526-0

VW EMERGENCY BRAKE HANDLE KIT

Show quality chrome emergency brake handle

For VW Type 1 Beetle, Buggy, and Sandrail

Complete stock replacement brake handle assembly includes:

1 handle, rod, spring, gear, ratchet, ratchet pin, anchor pin, button, washer & 2 clips

CUSTOM PEDAL COVERS

EMPI 4550 Pedal Cover, Brake & Clutch, Pair

Custom Pedal Covers...the finishing touch to any interior. Our custom pedal covers are chrome with rubber foot contact inserts.

Fits:

All Type 1

Type 2 55-67

All Type 3

EMPI 4551 VW Bug Brake, Clutch & Accelerator Pedal Assembly Covers, 3-Piece Set

VW CUSTOM PEDAL COVERS

A complete Custome VW pedal cover assembly... the finishing touch to any interior! Chrome pedals with rubber foot contact inserts.

Fits All:

Type 1

Type 2, 55-67

All Type 3s.

EMPI 4552 Pedal Cover, Accelerator Only, Each

CUSTOM PEDAL COVER

EMPI 4552 Pedal Cover, Accelerator Only, Each

The finishing touch to any interior. Our Custom pedal covers are chrome with rubber foot contact inserts.

Fits:

All Type 1

Type 2 55-67

All Type 3

VW TYPE 4 PROGRESSIVE CARBURETOR CONVERSION KIT

Accelerate with two barrel performance...Cruise with one barrel economy!

Complete kit includes.......Carburetor with Electric Choke - Manifold - Air Cleaner with Gauze element - Fuel Line - All Necessary Hardware.

WEBER DUAL 40 IDF CARBURETORS

Upgrade your carburetors to dual Weber 40IDF's today! This dual weber kit is a must for your performance dual port engine. Comes complete with everything needed for installation.

Fits Type 4 Volkswagen dual port engines

VW HEAVY DUTY THROTTLE CABLE KIT

Throttle cable is 9". Plastic tubing is included.

Comes with roller pedal.

EMPI 5002 Oil Pump Puller

In just minutes you can pull out your old oil pump without damaging your engine case with this simple to use oil pump puller. For 6mm & 8mm pump bodies.

VW FLYWHEEL LOCK TOOL

This Volkswagen universal flywheel lock woks on both 6 and 12 volt flywheels. Bolting through the engine case, it locks the flywheel securely in position for removal and installation of the gland nut.

EMPI 5004 Crankshaft & Flywheel Drill Fixture

Crankshaft & Flywheel Drill Fixture

VW HEATER BOX FLANGED J-TUBES

J-tubes replace stock heater boxes, eliminating heater and saving weight. The high tech finish offers the ultimate in protection and appearance.

Unnaffected by high heat associated with exhausts, the ceramic clean silver finish will continue to protect the exhaust system from the elements long after other conventinal coatings have burned away.

Includes gaskets

Sold in pairs

EMPI 5748 Axle Nut Tool 36mm

36mm axle nut removal tool commonly known as a "wacker" because you wack it with a hammer to remove the axle nuts. 36mm size for Type 1 & Type 3 Ghia. Use with 1/2" torque wrench to tighten nut.

46mm axle nut removal tool commonly known as a "wacker" because you wack it with a hammer to remove the axle nuts.

46mm size.

EMPI 5759 Valve Lifter Retaining Clips. Pair

Valve Lifter Retaining Clips

Holds lifters in place during engine assembly

VW OIL FILLER NUT TOOL

1/2" Drive

Easily remove and install oil filler with this tool

36MM GLAND/AXLE NUT SOCKET

This 12 point 36mm Gland/Axle nut socket is used to remove flywheel/gland or axle nuts along with your breaker bar.

VW BUG 17mm TRANSMISSION TRANSAXLE DRAIN PLUG SOCKET

6 SIDES

3/8" DRIVE

ALSO FOR USE ON IRS REAR TRAILING ARM PIVOT BOLTS

C.V. Joint Socket

12-point 8mm hex, 3/8" drive

EMPI 62-3020 3-Piece Firewall Kit, Louvered, Each

3 PC. STAINLESS STEEL FIREWALL KITS

Give your VW that show car finish with these highly polished Stainless steel firewall panels. Fits Type 1, Bugs (excluding convertible).

Large piece is louvered and side pieces are smooth.

EMPI 62-3030 3-Piece Firewall Kit, Smooth, Each

3- PIECE SMOOTH FIREWALL KITS

Give your VW that show car finish with these highly polised Stainless Steel firewall panels.

Fits: Type 1, Bugs (Excluding Convertible).

All 3 pieces are smooth

VW HOOD HANDLE

This aluminum VW hood handle guard fits Type 1s 1968 & newer.

Includes gasket

VW REAR FENDER GUARDS PAIR

Protect your Volkswagen's paint from stones and road debris with our fender guards.

Includes plastic trim.

VW FRONT FENDER GUARDS PAIR

Protect your Volkswagen's paint from stones and road debris with our fender guards.

Includes plastic trim

VW LOUVERED HEADLIGHT EYEBROWS PAIR

For Beetle Bug 1967 and on & early Splitty Bus

Provides that custom or classic look

VW CAT EYES HEADLIGHT COVERS PAIR

For Beetle Bug 1967 and newer

Provides that custom or classic look

VW FRONT TURN SIGNAL SEALS & WIRING

High quality Volkswagen front turn signal seals include attached wiring tube just like the originals.

Fits 1958-1963 Type 1 Volkswagens

VW FRONT TURN SIGNAL SEALS & WIRING

High quality Volkswagen front turn signal seals include wiring tube just like the originals.

Fits 1964-1969 Type 1 Volkswagens

VW FRONT TURN SIGNAL SEALS

Pair of high quality Volkswagen front signal seals

Fits 1970-79 Type 1 Volkswagens

VW TAIL LIGHT SEALS PAIR

For 1962-1967 Type 1s

VW TAIL LIGHT SEALS PAIR

For 1968-1970 Type 1 Volkswagens

VW REAR TAIL LIGHT SEALS PAIR

For 1971-72 Type 1 Volkswagens

VW LICENSE LIGHT SEAL

Fits Type 1 1967-79 Volkswagens