EMPI 17-2795 King Pin Conversion Inner Bearing

VW KING PIN CONVERSION BEARING, OUTER

This outer bearing allows you to install ball joint rotors onto king pin spindles.

Requires new seals

Intake Manifold 30/31/34 Pict

EMPI 17-2805 Intake Manifold 30/31/34 Pict (Ref. P/N: 113-129-701AQ)

This manifold allows for the use of 30 PICT-1, 31 PICT-3 or 34 PICT-3 carburetors without adaptors.

Manifold flange is drilled for either stud pattern and comes with heat risers, gaskets, and 1/8" pipe plug.

Drilled and tapped for optional vacuum advance.

EMPI 17-2809 BILLET F/F OIL LINE BRACKET - BLACK, EACH

Billet full flow hose brackets.

Keep oil lines in check while maintaining that Billet look. Bolts on at exhaust flange and helps protect oil lines from engine and exhaust. Fits up to 3/4" O.D. Hose.

Also comes Polished, P/N: 17-2810

EMPI 17-2810 BILLET F/F OIL LINE BRACKET - POLISHED, EACH

Billet full flow hose brackets.

Keep oil lines in check while maintaining that Billet look. Bolts on at exhaust flange and helps protect oil lines from engine and exhaust. Fits up to 3/4" O.D. Hose.

Also comes in black, P/N: 17-2809

VW BUG ENGINE NARROW OIL SUMP W/ FILTER

Cast aluminum oil sump is only 1 3/4" deep. Adds oil capacity and offers improved filtration and easy bolt on installation. Filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

VW MINI OIL SUMP WITH FILTER

Cast aluminum mini sump.

Replaces your stock oilscreen and cover and offers improved filtration, helps prevent oil starvation during hard cornering and easy bolt-on installation.

Filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

VW BUG ENGINE CASE OIL DUAL BYPASS ADAPTER

This adapter allows you to run both your stock oil cooler, along with an external cooler and/or a remote oil filter.

Fits VW Type 1 with minimal trimming of the sheetmetal. Will not fit doghouse-style coolers.

VW OIL SUMP FILTER

Replacement filter for 17-2871 & 17-2872

Offers improved filtration as easy filter design allows for unimpeded oil flow even if the filter gets plugged. Stainless steel micron filter can be cleaned and reused.

EMPI 17-2878 - VW Bug Type 1 Dual Circuit Master Cylinder Reservoir Mounts on Top

Billet Combo Fuel Pump Block-off/Coil Mount

EMPI 17-2926 Billet Combo Fuel Pump Block-off/Coil Mount

Polished aluminum Combo Mount serves as a fuel pump block-off, breather vent and ignition coil holder.

Features a 3/8 NPT outlet for vent.

Great looking and functional.

Hardware and gasket included.

EMPI 17-2941 OIL FILLER & BREATHER BOX KIT

The EMPI dual-purpose Oil Filler & Breather Box includes a system of internal baffles that separate the oil from the air then returns the oil back to the engine. It mounts upright on the alternator stand making for easy oil filling and was designed to look like part of the engine. The Billet Aluminum filler cap seals with an o'ring. Aluminum construction offers great looks and leak-free operation featuring an o'ring seal and button-head allen top screws. Vent your valve covers, crankcase, air cleaners...whatever your requirements. Comes with attaching nut, o'rings, gasket and instructions.

EMPI 17-2943 BILLET OIL FILLER CAP

Polished Billet Aluminum Cap with knurled edge for easy grip offers a great finishing touch to any breather tube.

Fits: P/N 17-2941 and alternator stands.

EMPI 17-2946 BILLET ALUMINUM OIL COOLER BLOCK-OFF

Billet Aluminum Oil Cooler Block-off

Show quality Polished Billet Aluminum oil cooler block-off. 

Comes with Allen Head Cap Screws for a clean installation along with gasket and hardware.

EMPI 17-2976 Rubber Flange Gauze Air Cleaner

Oval Gauze Rubber Flange Air Cleaner for Stock VW Carb., 2" Neck, 4 7/16"x6 7/8"x2 3/4" High

Featuring a washable and reusable Chrome top and Gauze Filter, they add style and performance and fit most upright applications. Constructed with a super strong molded pliable rubber lfange which absorbs vibration. Neck can be stretched up to 1/16" for added applicatons. Use with or without 90 degree Nylon Vent tube (included). Comes with clamp.

VW BRAKE MASTER CYLINDER

22.2mm

For all Volkswagen Type 2 to 1967

EMPI 1.25 Rocker Arms, W/Bushing, Set

1.40 ROCKER ARMS

EMPI 2164 EMPI 1.40 Rocker Arms, w/Bushing, Set

These superior quality chromoly rockers are just the answer for either a mild street or a hi-performance competition engine.

EMPI's rocker arms are made from forged chromoly and then precision ground and heat treated.

Not only are these the strongest rocker arms available, they are also drilled through on the alloy adjusting screws so both screws and rocker arms are fully lubricated.

All shafts, blocks and shims are high strength alloy as well. Precision ground bronze bushings with through hole lubrication ensures that premature failure of the old needle bearing rocker arm design is a thing of the past.

Chromoly rocker arm studs are provided to complete this kit and make installation and use a trouble free experience.

HI PERFORMANCE ROCKER SHAFT KITS

EMPI 21-2308 Hi-Performance Rocker Shaft Kit w/floating Center Spacer

Increase the RPM potential of your engine and get more power.

EMPI's rocker shaft kits help eliminate rocker shaft side play that casues rocker arm galling, clip and washer failure.

Has a floating aluminum center spacer which allows for "fine tuning" of rocker arm geometry and positioning.

All necessary hardware is included.

Increase the RPM potential of your air cooled Volkswagen engine and get more power.

EMPI 21-2309 Hi Performance/high Strength Rocker Shaft Kit

Our high-strength Rocker Shaft Kit helps eliminate rocker shaft side play that causes rocker arm galling and clip & washer failure.

Our kit includes two precision ground high strength shafts, hardened steel spacers & solid shims, and all necessary installation hardware is included.

Can be used with either stock 1:1 rockers or our high performance 1.25:1 rockers for added power!

Best when used with EMPI's swivel foot adjusters.

EMPI 21-2310 Rocker Arm Stand Shims, 12 pcs

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Includes 4pcs., each of .015", .030", and .060"

An easy and inexpensive way to get more power and acceleration from any 1200-1600cc Volkswagen engine.

No special modifications are needed!

Works with stock VW rocker shafts, push rods, and adjusters!

These 1.25 Rocker arms will not affect cam duration; they increase lift throughout the entire cycle.

Does not sacrifice bottom end performance and can be run with stock carburetors.

Set of new screws and new nuts to use for adjusting the valves on a Type 1 VW valve train

Works with our 1.25:1 rocker arms too!

Chromoly rocker studs are superior in strength to stock VW rocker studs

A must have for high-performance heads with dual valve springs!

Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold in sets of four.

Chromoly rocker studs are superior in strength to stock VW rocker stud

A must have for high-performance heads with dual valve springs!

Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold each.

ROCKER ARM STAND SHIMS

EMPI 21-2315 Rocker Arm Shims, .015", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

ROCKER ARM STAND SHIMS

EMPI 21-2330 Rocker Arm Shims, .030", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

ROCKER ARM STAND SHIMS

EMPI 21-2360 Rocker Arm Shims, .060", Set of 4

Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.

Set of 4

EMPI 21-4310 VW High Grade Camshaft Gear Bolts

Cam Vw Bug Set of 3 for attaching P/N 21-2500 aluminum cam gear.

VW .03" CYLINDER HEAD SPACERS

VW steel cylinder head spacers (.030") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. For VW 1500-1600cc engines.

VW .06" CYLINDER HEAD SPACERS

VW steel cylinder head spacers (.060") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. For VW 1500-1600cc engines.

VW .010" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs.

Fits VW Type 1 engines.

For 85.5mm cylinders.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines. For 85.5mm cylinders.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines.  For 85.5mm cylinders.

VW .04" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines. For 85.5mm cylinders.

VW CYLINDER SHIMS

.060" cylinder shims for VW Type 1. 85.5mm cylinders

These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs.

VW .09" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs.Fits VW Type 1 engines. For 85.5mm cylinders.

VW .01" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders. For VW Type 1 engines.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .04" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders.

VW .060" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 and 92mm bore VWs.

90.5mm/92mm Cylinder Shims

EMPI 21-7076 90.5mm/92mm Cylinder Shims .090"

Steel shims allow for adjusting deck height without machining the pistons.

Corrects for increase in stroke and compensates when case is surface machined.

For standard 8mm studs and 10mm studs.

Sold in sets of 4.

VW CYLINDER SHIMS

.010" cylinder shims for VW Type 1. 94mm cylinders

These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs.

VW .02" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs.

VW .03" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs.  Set of 4. Fits 94mm bore VWs.

VW .040" CYLINDER SHIM SET

Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs.  Set of 4.  Fits Type 1 VWs with a 94mm big bore.