EMPI

VW THROTTLE CABLE EXTENDING KIT

2-piece Volkswagen throttle cable extending kit that can be installed onto the existing end of a throttle cable.

VW TRANSMISSION MOUNT KIT

This Volkswagen Bug to Bus transmission mount kit allows for installing a Type 2 I.R.S. transmission into a Type 1 chassis. Featuring a heavy duty steel saddle, mount, and straps, eliminate your stock mounts & saddle for maximum support with no flex. A must for competition use!

Your particular application will dictate the proper axle length needed. CV's and components you may need.

VW THROWOUT BEARING

This EMPI branded throwout bearing fits VW models 1970 & earlier: Bug / Beetle, Karmann Ghia, Type 2 Bus Transporter, and Type 3.

VW LARGE INTAKE BOOT CLAMPS

Sold in pairs.

VW INTAKE MANIFOLD GASKETS

Fits Type 2 & Type 4 engines; 1700-2000CC. 3 & 4 bolt gaskets.

Sold in pairs.

EMPI 3245 Carburetor Adaptor For Alternator Conversion

Sometimes necessary when doing an alternator conversion. Spaces up the stock carburetor.

Comes with studs, nuts, and gaskets.

FOR 28/30 PICT CARBURETORS ONLY!

VW INTAKE MANIFOLD GASKETS

Dual port Volkswagen intake manifold gaskets with larger intake face.

Sold in pairs.

EMPI 33-5000 OIL THERMOSTAT ONLY W/3/8" NPT

Mounts in-line and bypasses oil cooler until oil warms up to approximately 175 degrees. 

Always partially open to avoid over pressurizing. 

A must in performance and cold-weather applications.

Sold separately, fittings P/N: 9211 or 9212 and clamps P/N: 9225

For complete kit with fittings and clamps P/N: 33-5010

EMPI 33-5010 OIL THERMOSTAT W/FITTINGS AND CLAMPS

Mounts in-line and bypasses oil cooler until oil warms up to approximately 175 degrees. 

Always partially open to avoid over pressurizing. 

A must in performance and cold-weather applications.

VW CARBURETOR BASE GASKETS

TWO Base gaskets for 40/44 IDF/DRLA Volkswagen carburetors.

VW TYPE 1 ALUMINUM HEATER HOSE

Contains no paper. Heat and corrosion resistant to 450 degrees.

Sold Each

VW MUFFLER FLANGE GASKETS

Package of two VW small 3 bolt exhaust flange gaskets

EMPI 3395 Exhaust Port Gasket, 1200-1600cc, 1 5.8"

Pack of 4

VW CARBURETOR BASE GASKET

A VW carburetor base gasket for Weber Carburetors; 40/44/48 IDA Gasket

EMPI 3405 Muffler Flange Gasket, 2-Bolt

Pack of 2

VW HEAT RISER BLOCK-OFF PLATES

These block-off plates cover heat riser flanges when intake heat riser is not used. A must when installing most dual carburetor kits.

Includes gaskets.

VW FRONT LEFT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails. Requires cutting fitting and welding.

VW FRONT RIGHT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails.  Requires cutting fitting and welding.

VW REAR LEFT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails. Requires cutting fitting and welding.

VW REAR RIGHT FLOOR PANEL

Don't install your new carpet over dangerous, old rusted-out floors! Metal replacement floor panels make it fast and easy to make repairs.

Fits VW Type 1 beetle chassis manx, dune buggy

Without seat rails.  Requires cutting fitting and welding.

VW EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 1 & Ghia 1200-1600cc. Will NOT work with Type 3.

All systems include aluminum flex hose and installation kit.

VW DUAL QUIET EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 1 & Ghia, 1300-1600cc, 66-73

All systems include aluminum flex hose and installation kit.

VW EXHAUST SYSTEM

The most popular of our extensive precision-designed VW exhaust systems. These systems feature 1 3/8" tubing with small 3 bolt muffler flange and flared chrome muffler tips.

Fits Type 3, 1500-1600CC.

All systems include aluminum flex hose and installation kit.

VW MUFFLER FLANGE

Small 3 bolt Volkswagen muffler flange

1 3/4" I.D.

DUAL PORT ENGINE CHROMOLY CASE STUD KIT

These 10mm chromoly case studs provide the superior and even clamping force required by today's high performance air cooled VW engines. The high grade chromoly studs are precision machined to resist stress and fatigue and are made for dual port head based engines.

For VW Type 1 71-79, Ghia 71-74, Type 2 71, & Type 3 71-73

Includes O.E. style hardened washers and hex nuts.

CHROMOLY CASE STUDS

EMPI 4010 10mm Chromoly Case Studs +12.7mm for Duel Port Heads VW

10mm C/M Case Studs +12.7mm for Duel Port Heads CHROMOLY CASE STUDS EMPI's Chromoly Case Studs provide superior and even clamping force required by today's hi-performance VW engines.

Our Chromoly Studs are made from high-grade Chromoly and precision machined to resist stretch and fatigue.

EMPI Chromoly Case Studs are available with 8mm or 10mm threads, stock length or +12.7mm longer for stroker applications or other variables.

Each kit is complete with O.E. style hardened washers and hex nuts.

VW CASE SAVERS

Repair stripped and worn head stud threads with these Volkswagen case saver inserts. Provides a great hold and comes in sets of 8.

(10mm ID x 1/2" O.D.)

VW DELUXE ENGINE HARDWARE KIT

You get all the necessary hardware you need to assemble your VW beetle-style engine just the way it rolled off the line! This 8mm set includes case half sealing nuts, 15mm head nuts, and extra thick hardened washers.

VW DELUXE ENGINE HARDWARE KIT

You get all the necessary hardware you need to assemble your VW beetle-style engine just the way it rolled off the line! This 10mm set includes case half sealing nuts, 15mm head nuts, and extra thick hardened washers.

DUAL PORT ENGINE CHROMOLY CASE STUD KIT

These 8mm chromoly case studs provide the superior and even clamping force required by today's high performance air cooled VW engines. The high grade chromoly studs are precision machined to resist stress and fatigue and are made for dual port head based engines.

For VW Type 1 71-79, Ghia 71-74, Type 2 71, & Type 3 71-73

Includes O.E. style hardened washers and hex nuts.

Replaces original VW part #043-198-035DP.

VW CHROMOLY CASE STUD KIT

This is an 8mm chromoly case stud kit +12.7mm longer for stroker applications or other variables.

These case studs provide superior and even clamping force required by todays high-performance engines. The chromoly studs are made from high grade chromoly and precision machined to resist stress and fatigue. For dual port heads.

Includes O.E. style hardened washers and hex nuts.

10MM SELF TAPPING CASE STUD

A quick repair for stripped head studs. The rolled threads of this 10mm stud provide maximum hold and metal chips are effectively collected by the slot or hole design. Hole shown in picture but could have slot.

Measures 9 3/8" (240mm) long.

HI-PERFORMANCE CHROMOLY GLAND NUT - 36MM

EMPI 4026 Chromoly Gland Nut w/washer

Don't take a chance on stock gland nuts in high performance applications.

This ultra strong bad boy is made from 4130 chromoly. 

The extra strength chromoly and concave spring steel washer provide maximum holding power. Fitted with special pre-greased needle bearing and grease seal. 

Compatible with stock 4 dowel pin and 8 dowel pin flywheels and features a 36mm nut size, NOT a 1 7/8"

VW GLAND NUT WASHER

Heavy duty gland nut washer for Type 1 Volkswagen applications.

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.015" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.030" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.060" shims... sold in sets of eight!

Replace the wave washers on the stock rocker shaft set-up

Eliminates excess side play, and maintains proper valve train geometry.

.010" shims... sold in sets of eight!

Prevent valve stem wear caused by the side load of high lift cams and high valve spring pressure.

SOAK OVERNIGHT IN OIL BEFORE INSTALLING

CHECK OIL HOLES IN ROCKERS FOR FREE FLOW

VW 85.5MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 85.5mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 90.5MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 90.5mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 92MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 92mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

VW 94MM PISTON PIN BUTTON SET

Prevent costly engine damage with these VW 94mm teflon piston pin retainer buttons. The failure of the small and fragile stock clips that are easily damaged during installation can cause total engine destruction. Teflon retainers are easy to install and will not break or wear out. Easy press-in installation.

Pressure Plate

EMPI 4080, 1700lb/ Pressure Plate (Boxed).

The latest addition to the EMPI high performance line. Perfect for drag race, sand/off-road or high performance street applications. This 200mm pressure plate is rated at 1700 lbs, and are factory balanced with the removable center ring to cover both early and late transmission.

EMPI 4099 CHROMOLY FLYWHEEL, 12-VOLT, 200MM

This chromoly version of our lightened flywheel is the answerfor anyone looking ofr the ultimate in durability under extreme conditions. One piece chromoly construction and offset 8-dowel hole pattern along with a weight of approximately 13lbs., make this fully balanced flywheel the best option for a high performance engine. 12-volt 200mm (130 teeth) O-ring style.