EMPI 17-2976 Rubber Flange Gauze Air Cleaner
Oval Gauze Rubber Flange Air Cleaner for Stock VW Carb., 2" Neck, 4 7/16"x6 7/8"x2 3/4" High
Featuring a washable and reusable Chrome top and Gauze Filter, they add style and performance and fit most upright applications. Constructed with a super strong molded pliable rubber lfange which absorbs vibration. Neck can be stretched up to 1/16" for added applicatons. Use with or without 90 degree Nylon Vent tube (included). Comes with clamp.
$21.95
|
EMPI 1.25 Rocker Arms, W/Bushing, Set
These superior quality chromoly rockers are just the answer for either a mild street or a hi-performance competition engine.
EMPI's rocker arms are made from forged chromoly and then precision ground and heat treated.
Not only are these the strongest rocker arms available, they are also drilled through on the alloy adjusting screws so both screws and rocker arms are fully lubricated.
All shafts, blocks and shims are high strength alloy as well. Precision ground bronze bushings with through hole lubrication ensures that premature failure of the old needle bearing rocker arm design is a thing of the past.
Chromoly rocker arm studs are provided to complete this kit and make installation and use a trouble free experience.
$199.95
|
Increase the RPM potential of your air cooled Volkswagen engine and get more power.
EMPI 21-2309 Hi Performance/high Strength Rocker Shaft Kit
Our high-strength Rocker Shaft Kit helps eliminate rocker shaft side play that causes rocker arm galling and clip & washer failure.
Our kit includes two precision ground high strength shafts, hardened steel spacers & solid shims, and all necessary installation hardware is included.
Can be used with either stock 1:1 rockers or our high performance 1.25:1 rockers for added power!
Best when used with EMPI's swivel foot adjusters. $79.95
|
EMPI 21-2310 Rocker Arm Stand Shims, 12 pcs
Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.
Includes 4pcs., each of .015", .030", and .060" $13.95
|
An easy and inexpensive way to get more power and acceleration from any 1200-1600cc Volkswagen engine.
No special modifications are needed!
Works with stock VW rocker shafts, push rods, and adjusters!
These 1.25 Rocker arms will not affect cam duration; they increase lift throughout the entire cycle.
Does not sacrifice bottom end performance and can be run with stock carburetors. $119.95
|
Set of new screws and new nuts to use for adjusting the valves on a Type 1 VW valve train
Works with our 1.25:1 rocker arms too! $21.95
|
Chromoly rocker studs are superior in strength to stock VW rocker studs
A must have for high-performance heads with dual valve springs!
Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold in sets of four. $24.95
|
Chromoly rocker studs are superior in strength to stock VW rocker stud
A must have for high-performance heads with dual valve springs!
Installs without modification in Type 1, Type 2, and Type 3 1500-1600cc based heads. Sold each. $5.95
|
ROCKER ARM STAND SHIMS
EMPI 21-2315 Rocker Arm Shims, .015", Set of 4
Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.
Set of 4 $5.95
|
ROCKER ARM STAND SHIMS
EMPI 21-2330 Rocker Arm Shims, .030", Set of 4
Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.
Set of 4 $5.95
|
ROCKER ARM STAND SHIMS
EMPI 21-2360 Rocker Arm Shims, .060", Set of 4
Designed to go between the rocker stand and the head boss for correct rocker arm height and geometry.
Set of 4 $5.95
|
EMPI 21-4310 VW High Grade Camshaft Gear Bolts
Cam Vw Bug Set of 3 for attaching P/N 21-2500 aluminum cam gear. $5.95
|
VW .03" CYLINDER HEAD SPACERS
VW steel cylinder head spacers (.030") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. For VW 1500-1600cc engines. $17.95
|
VW .010" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs.
Fits VW Type 1 engines.
For 85.5mm cylinders.
$15.95
|
VW .03" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8 mm studs. Fits VW Type 1 engines. For 85.5mm cylinders. $15.95
|
VW CYLINDER SHIMS
.060" cylinder shims for VW Type 1. 85.5mm cylinders
These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs. $15.95
|
VW .01" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders. For VW Type 1 engines. $15.95
|
VW .02" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 90.5 & 92mm cylinders. $15.95
|
90.5mm/92mm Cylinder Shims
EMPI 21-7076 90.5mm/92mm Cylinder Shims .090"
Steel shims allow for adjusting deck height without machining the pistons.
Corrects for increase in stroke and compensates when case is surface machined.
For standard 8mm studs and 10mm studs.
Sold in sets of 4. $15.95
|
VW CYLINDER SHIMS
.010" cylinder shims for VW Type 1. 94mm cylinders
These steel shims allow for adjusting the deck height without machining the pistons. Corrects for increase in stroke and compensates when the case is surface machined clearanced for standard 8mm studs. $12.95
|
VW .02" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs. $15.95
|
VW .03" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits 94mm bore VWs. $15.95
|
VW .040" CYLINDER SHIM SET
Steel shims allow for adjusting deck height without machining the pistons. Corrects for increase in stroke and compensates when case is surface machined clearanced for standard 8mm studs. Set of 4. Fits Type 1 VWs with a 94mm big bore. $15.95
|
VW .04" CYLINDER HEAD SPACERS
VW steel cylinder head spacers (.040") allow for adjusting deck height easily without removing the cylinders. Compensates for zero deck height when heads have been machined, or in stroker setups. Set of 4. $15.95
|
VW FRONT END ADJUSTER, BALL JOINT
For use on models from 1966 and LATER
Requires one on each tube; cutting and welding required! $22.95
|
VW FRONT END ADJUSTER, LINK PIN
For use on models from 1965 and prior.
Requires one on each tube; cutting and welding required! $22.95
|
VW REAR DISC BRAKE CONVERSION KIT
VW rear disc brake conversion kit with emergency handbrake for all IRS & Swingaxle Type 1s. Includes Beetles, Buggys, Sandrails. Kits are available for both swing axle and IRS Type 1 based applications. All kits come complete with rotors, calipers, cables all necessary hardware. This deluxe kit comes with HD cast mounting brackets
Standard 4x130 bolt pattern $549.95
|
Front Disc Brake Kit
Wide 5 VW Bolt Pattern
EMPI 22-2880 Front Disc Brake Kit, Link Pin, 5 lug, 5/205, 15" Rims to 65
A special brake rotor and caliper mount bracket combined to give you a premium disc brake upgrade using your existing front spindles.
Kit comes complete with master cylinder, brake lines, floating calipers with brake pads, wheel bearings, grease seals and all necessary hardware.
Now you can have the stopping power of disc brakes and have the early 5 on 205 rim of your choice, and no adapters!
WILL NOT WORK WITH DROP SPINDLES.
Caliper guide pins pre-installed. $529.95
|
|
VW Bug Type 1 Wide 5 Rear Disc Brake Kit - With Emergency Brake
$549.95
|
Wide Rear Disc Brake Kit w/o E-Brake
EMPI 22-2930 Wide Rear Disc Brake Kit w/o E-Brake
5/205, Swing Axle 58-67 Wide Track rear disc brake kits are for Off-Roaders who are looking to increase their rear wheel "track".
Kits are without emergency brakes, and come complete with 1-piece minimum offseet 1" extra wide rotors, calipers, pads, mounting brackets, and all necessary hardware and gaskets for the complete installation.
Rotors are threaded for 12mm and 14mm studs. $499.90
|
PADS FOR STEEL BRACKET KITS
EMPI 22-2966 Pads for Steel Bracket Kits
Set of 4 $34.95
|
VW FRONT DISC BOLT-ON BRAKE KIT
VW front disc brake kit for link pin style applications. Bolt-on 5/130 pattern.
Kit includes bolt-on heavy duty brackets and conversion bearings. Hardware included. Four bolt pattern shown for picture only. $449.95
|
Carburetor Tune up Kit
EMPI 2202 Carburetor Tune up Kit WEBER Progressive, DFV, Holley 5200, EPC 32/36F (VW).
Basic repair kit come complete with needle/seat, all necessary o-rings and gasket.
Kit also includes floats and accelerator pump diaphragms.
$49.95
|
Carburetor Tune up Kit
EMPI 2238 Carburetor Tune up Kit Holley Bug Spray
Basic repair kit comes complete with needle/seat, all necessary o-rings and gasket. $24.99
|
Carburetor Tune up Kit Zenith 32NDIX - Minor
EMPI 2258 Carburetor Tune up Kit Zenith 32NDIX - Minor.
Basic repair kit come complete with needle/seat, all necessary o-rings and gasket. $39.95
|
VW CARBURETOR REPAIR KIT
Basic VW carburetor repair kits comes with accelerator pump diaphram, needle/seat, and all necessary o-rings & gaskets.
Note: kit includes all parts needed for one carburetor; if dual carb engine, two kits are needed.
Kit parts include only what you see in picture $44.95
|
|
REBUILD KIT FOR ONE CARB - WEBER 40-44 IDF
$44.95
|
EMPI 2365 Carburetor Tune-up Kit
WEBER 34 ICH, EPC 34X
34ICT
The kit is a basic repair kit and comes complete with needle/seat, all necessary 0-rings and gaskets.
$29.95
|
Melling Heavy Duty Oil Pump Type 1 Beetle Flat Cams
$145.00
|
Electric Fuel Pump Mount Kit
EMPI 31-3010 Electric Fuel Pump Mount Kit
Fuel Pump Mount Kit allows for the installation of EMPI or Facet electric fuel pumps in the stock pump location. Hardware and gasket included. $24.95
|
Billet Fuel Pump Block-off w/hardware
EMPI 31-3011Billet Fuel Pump Block-off w/hardware
Fuel Pump Block-off/Mount Block off with 12mm threaded breather boss.
Block off in high tech polished Billet aluminum. Includes mounting gasket. $29.95
|
EMPI 3137 Replacement Pins & Clips, Long, Pair $12.95
|
EMPI 3157 Belly Pan Gasket
Installs between body and pan providing a water-tight seal.
Great for body-off restorations, Kits cars, Baja Bugs and Dune Buggies $24.95
|
Black roller pedal that allows smoother acceleration for your air cooled vw! Fits all Type 1s, Beetle, Buggy, Ghia, and Sandrail.
$12.95
|
VW CABLE SHORTENING KIT
Shorten your clutch, emergency brake and throttle cables quickly.
A must for all buggies that have shortened pans. $19.95
|
CLUTCH CABLE SHORTENING KIT
Shorten your clutch cable quickly and easily.
A must for off-road Buggies! $6.95
|
VW E-BRAKE CABLE SHORTENING KIT
Shorten your emergency brake cable quickly and easily.
A must for Volkswagen Buggies with shortened pans. $10.90
|
VW THROTTLE CABLE SHORTENING KIT
Shorten your Volkswagen throttle cable quickly and easily.
End is designed for use with barrel nut. $5.95
|
